,
Réseau européen de revendeurs de machines de stockage

Bitte einen Suchbegriff eingeben - Veuillez entrer un terme de recherche
Catégorie:
    Fabricant:
      Machines:
        Commerçant:

          Plate Shear - Mechanical

          Machinelist: Plate Shear - Mechanical


          Plate Shear - Mechanical

          used Sheet metal working / shaeres / bending Plate Shear - Mechanical KAPEMA SMP 20-20


          • Plum & Partner Werkzeugmaschinen GmbH
          • Winkelstraße 32
          • 32257 Bünde
          • Deutschland

          • +49 05223 574444
            +49 5223188330
          • info@plum-maschinen.de
            www.plum-maschinen.de
          #1082-08037 · Plate Shear - Mechanical

          KAPEMA - SMP 20-20 - - Fabrikneu / new -

          Technical details
          sheet width 2050 mm︱plate thickness 2 mm︱strokes per minute until 38 ︱cutting angle 1,75 °︱table height over floor 870 mm︱total power requirement 3 kW︱weight of the machine ca. 1520 kg︱range L-W-H 2,2 x 0,6 x 1,2 m︱Electric 380 Volt ︱Back stop with manual adjustment ︱Shadow line lighting ︱Foot switch
          The new motor guillotine type SMP is a well dimensioned machine with all-welded link guides. The drive takes place with a Standard geared brake motor via a chain connection to the main axle. the Knives are of the highest quality. The optimal cutting angle secures the Together with the rubber-covered blank holder perfect cuts. Bearings and guides are maintenance and lubrication-free. Standard equipment: • Back gauge 665 with mm scale. • cutting edge lighting. • Section counter. • Table extensions 600 mm. • Right angle stop, left. • Movable 24 V foot switch with emergency stop. • Motor protection switch and emergency stop. • 2 cutting edges per knife. • Rear protective grille, warranty = 12 months for single-shift operation. Other models: 1275 x 3mm, 1250 x 4mm, 2050 x 2mm Machine dealer with own stock of 1600 m².
            sheet width 2050 mm
            plate thickness 2 mm
            strokes per minute until 38
            cutting angle 1,75 °
            table height over floor 870 mm
            total power requirement 3 kW
            weight of the machine ca. 1520 kg
            range L-W-H 2,2 x 0,6 x 1,2 m
            Description :
            The new motor guillotine type SMP is a well dimensioned machine with
            all-welded link guides. The drive takes place with a
            Standard geared brake motor via a chain connection to the main axle. the
            Knives are of the highest quality. The optimal cutting angle secures the
            Together with the rubber-covered blank holder perfect cuts.
            Bearings and guides are maintenance and lubrication-free.
            Standard equipment: • Back gauge 665 with mm scale. •
            cutting edge lighting. • Section counter. • Table extensions 600 mm. •
            Right angle stop, left. • Movable 24 V foot switch with emergency stop.
            • Motor protection switch and emergency stop. • 2 cutting edges per knife. •
            Rear protective grille, warranty = 12 months for single-shift operation.
            Other models: 1275 x 3mm, 1250 x 4mm, 2050 x 2mm

            Machine dealer with own stock of 1600 m².


        • Plum & Partner Werkzeugmaschinen GmbH
        • Winkelstraße 32
        • 32257 Bünde
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical KAPEMA SMP 12-30


          • Plum & Partner Werkzeugmaschinen GmbH
          • Winkelstraße 32
          • 32257 Bünde
          • Deutschland

          • +49 05223 574444
            +49 5223188330
          • info@plum-maschinen.de
            www.plum-maschinen.de
          #1082-08408 · Plate Shear - Mechanical

          KAPEMA - SMP 12-30 - - Fabrikneu / new -

          Technical details
          sheet width 1275 mm︱plate thickness 3 mm︱strokes per minute until 35 ︱cutting angle 2,0 °︱table height over floor 870 mm︱thickness at "Niro-steel" 2 mm︱total power requirement 3 kW︱weight of the machine ca. 875 kg︱range L-W-H 1,7 x 1,68 x 1,1 m︱Electric 380 Volt ︱Back stop with manual adjustment ︱Shadow line lighting ︱Foot switch ︱Piece counter ︱Squaring arm ︱Support arms
          The guillotine shears type SMP is a well-dimensioned machine with all-welded gate guides. The drive takes place with a standard geared brake motor via a chain connection to the main axis. The knives are of the highest quality. The optimal cutting angle ensures together with the rubber-coated sheet metal holder, perfect cuts. Bearings and guides are maintenance-free and lubrication-free. Standard equipment: • Back gauge 635 with mm scale. • Cutting line lighting. • Section counter. • Table extensions 600 mm. • Right-angled stop, left. • Movable 24 V foot switch with emergency stop. • Motor protection switch and emergency stop. • 2 cutting edges per knife. • rear photocell. Pre-freight to our stock + packaging 270, -. Machine dealer with own stock of 1600 m².
            sheet width 1275 mm
            plate thickness 3 mm
            strokes per minute until 35
            cutting angle 2,0 °
            table height over floor 870 mm
            thickness at "Niro-steel" 2 mm
            total power requirement 3 kW
            weight of the machine ca. 875 kg
            range L-W-H 1,7 x 1,68 x 1,1 m
            Description :
            The guillotine shears type SMP is a well-dimensioned machine with
            all-welded gate guides. The drive takes place with a standard geared brake
            motor via a chain connection to the main axis. The knives are of the highest
            quality. The optimal cutting angle ensures together with the rubber-coated
            sheet metal holder, perfect cuts.
            Bearings and guides are maintenance-free and lubrication-free.
            Standard equipment: • Back gauge 635 with mm scale. •
            Cutting line lighting. • Section counter. • Table extensions 600 mm. •
            Right-angled stop, left. • Movable 24 V foot switch with emergency stop.
            • Motor protection switch and emergency stop. • 2 cutting edges per knife. •
            rear photocell.
            Pre-freight to our stock + packaging 270, -.
            Machine dealer with own stock of 1600 m².


        • Plum & Partner Werkzeugmaschinen GmbH
        • Winkelstraße 32
        • 32257 Bünde
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical KAPEMA SMP 20-30


          • Plum & Partner Werkzeugmaschinen GmbH
          • Winkelstraße 32
          • 32257 Bünde
          • Deutschland

          • +49 05223 574444
            +49 5223188330
          • info@plum-maschinen.de
            www.plum-maschinen.de
          #1082-08417 · Plate Shear - Mechanical

          KAPEMA - SMP 20-30 - - Fabrikneu / new -

          Technical details
          sheet width 2050 mm︱plate thickness 3 mm︱strokes per minute until 35 ︱cutting angle 2,0 °︱table height over floor 870 mm︱thickness at "Niro-steel" 2 mm︱total power requirement 4 kW︱weight of the machine ca. 1550 kg︱range L-W-H 2,5 x 1,57 x 1,21 m︱Electric 380 Volt
          The new motor guillotine type SMP is a well dimensioned machine with all-welded link guides. The drive takes place with a Standard geared brake motor via a chain connection to the main axle. the Knives are of the highest quality. The optimal cutting angle secures the Together with the rubber-covered blank holder perfect cuts. Bearings and guides are maintenance and lubrication-free. Standard equipment: • Back gauge 665 with mm scale. • cutting edge lighting. • Section counter. • Table extensions 600 mm. • Right angle stop, left. • Movable 24 V foot switch with emergency stop. • Motor protection switch and emergency stop. • 2 cutting edges per knife. • Rear protective grille, warranty = 12 months for single-shift operation. Other models: 1275 x 3mm, 1250 x 4mm, 2050 x 2mm Machine dealer with own stock of 1600 m².
            sheet width 2050 mm
            plate thickness 3 mm
            strokes per minute until 35
            cutting angle 2,0 °
            table height over floor 870 mm
            thickness at "Niro-steel" 2 mm
            total power requirement 4 kW
            weight of the machine ca. 1550 kg
            range L-W-H 2,5 x 1,57 x 1,21 m
            Description :
            The new motor guillotine type SMP is a well dimensioned machine with
            all-welded link guides. The drive takes place with a
            Standard geared brake motor via a chain connection to the main axle. the
            Knives are of the highest quality. The optimal cutting angle secures the
            Together with the rubber-covered blank holder perfect cuts.
            Bearings and guides are maintenance and lubrication-free.
            Standard equipment: • Back gauge 665 with mm scale. •
            cutting edge lighting. • Section counter. • Table extensions 600 mm. •
            Right angle stop, left. • Movable 24 V foot switch with emergency stop.
            • Motor protection switch and emergency stop. • 2 cutting edges per knife. •
            Rear protective grille, warranty = 12 months for single-shift operation.
            Other models: 1275 x 3mm, 1250 x 4mm, 2050 x 2mm

            Machine dealer with own stock of 1600 m².


        • Plum & Partner Werkzeugmaschinen GmbH
        • Winkelstraße 32
        • 32257 Bünde
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical RFR MS/24


          • Markus Hirsch GmbH
          • Hüttenstrasse 1
          • 46284 Dorsten
          • Deutschland

          • +49 2362 95035 12
            +49 2362 95035 10
          • liersch@hirsch-maschinen.de
            www.hirsch-maschinen.de
          #1077-01210 · Plate Shear - Mechanical

          RFR - MS/24 - - ca. 1960 -

          Technical details
          sheet width 2300 mm︱plate thickness 1,5 mm︱distance between columns 2400 mm︱impact length 1000 mm︱total power requirement kW︱weight of the machine ca. 0,5 t︱
            sheet width 2300 mm
            plate thickness 1,5 mm
            distance between columns 2400 mm
            impact length 1000 mm
            weight of the machine ca. 0,5 t


        • Markus Hirsch GmbH
        • Hüttenstrasse 1
        • 46284 Dorsten
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical RAS 53.60


          • EMUK GmbH Werkzeugmaschinen
          • Siemensstrasse 24 a
          • 76316 Malsch
          • Deutschland

          • +49 (0) 7246 1392
            +49 (0) 7246 1394
          • info@emuk.de
            www.emuk.de
          #1058-22062 · Plate Shear - Mechanical

          RAS - 53.60 - - 380/6 -

          Technical details
          sheet width 2000 mm︱plate thickness 2,25 mm︱distance between columns 2040 mm︱total power requirement 7,5 kW︱weight of the machine ca. 1,5 t︱dimensions of the machine ca. 2,2x1,7x1,1 m︱
            sheet width 2000 mm
            plate thickness 2,25 mm
            distance between columns 2040 mm
            total power requirement 7,5 kW
            weight of the machine ca. 1,5 t
            dimensions of the machine ca. 2,2x1,7x1,1 m
            Description :



        • EMUK GmbH Werkzeugmaschinen
        • Siemensstrasse 24 a
        • 76316 Malsch
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical HESSE by DURMA MS 1303


          • HESSE+CO Maschinenfabrik GesmbH
          • Straße 4 Objekt 8
          • 2351 Wiener Neudorf
          • Österreich

          • +43/2236/638 70-0
            +43/2236/636 62
          • office@hesse-maschinen.com
            https://www.hesse-maschinen.com
          #1069-1902 · Plate Shear - Mechanical

          HESSE by DURMA - MS 1303 - - 2024 -

          Technical details
          neu20249715April 2024, ZwischenverkaTürkei13500 €︱ 276.75 €︱ 1350 mm︱ 3 mm︱ 35 1/min︱ 550 mm︱ 3 kW︱ 2 Stk.︱ 850 mm︱ 400 mm︱ 1900 mm︱ 1350 mm︱ 1260 mm︱ 1060 kg︱
          manualback gauge automatic sheet hold down hold down with rubber pads moveable foot switch side lay 2 supporting arms light barriers on the back of the machine user manual in GERMAN and ENGLISH
            neu
            2024
            9715
            April 2024, Zwischenverka
            Türkei
            13500 €
            276.75 €
            1350 mm
            3 mm
            35 1/min
            550 mm
            3 kW
            2 Stk.
            850 mm
            400 mm
            1900 mm
            1350 mm
            1260 mm
            1060 kg
            Description :
            manualback gauge
            automatic sheet hold down
            hold down with rubber pads
            moveable foot switch
            side lay
            2 supporting arms
            light barriers on the back of the machine
            user manual in GERMAN and ENGLISH


        • HESSE+CO Maschinenfabrik GesmbH
        • Straße 4 Objekt 8
        • 2351 Wiener Neudorf
        • Österreich

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical HESSE by DURMA MS 2003


          • HESSE+CO Maschinenfabrik GesmbH
          • Straße 4 Objekt 8
          • 2351 Wiener Neudorf
          • Österreich

          • +43/2236/638 70-0
            +43/2236/636 62
          • office@hesse-maschinen.com
            https://www.hesse-maschinen.com
          #1069-461 · Plate Shear - Mechanical

          HESSE by DURMA - MS 2003 - - 2024 -

          Technical details
          neu20249716April 2024, ZwischenverkaTürkei15000 €︱ 307.5 €︱ 2050 mm︱ 3 mm︱ 35 1/min︱ 550 mm︱ 3 kW︱ 2 Stk.︱ 850 mm︱ 400 mm︱ 2600 mm︱ 1350 mm︱ 1260 mm︱ 1280 kg︱
          manualback gauge automatic sheet hold down hold down with rubber pads moveable foot switch side lay 2 supporting arms light barriers on the back of the machine user manual in GERMAN and ENGLISH WE HAVE MORE THAN 330 REFERENCES!
            neu
            2024
            9716
            April 2024, Zwischenverka
            Türkei
            15000 €
            307.5 €
            2050 mm
            3 mm
            35 1/min
            550 mm
            3 kW
            2 Stk.
            850 mm
            400 mm
            2600 mm
            1350 mm
            1260 mm
            1280 kg
            Description :
            manualback gauge
            automatic sheet hold down
            hold down with rubber pads
            moveable foot switch
            side lay
            2 supporting arms
            light barriers on the back of the machine
            user manual in GERMAN and ENGLISH

            WE HAVE MORE THAN 330 REFERENCES!


        • HESSE+CO Maschinenfabrik GesmbH
        • Straße 4 Objekt 8
        • 2351 Wiener Neudorf
        • Österreich

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 3050 x 4


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091082 · Plate Shear - Mechanical

          OSTAS - ORGM 3050 x 4 - - 2023 -

          Technical details
          sheet width 3050 mm︱plate thickness 4 mm︱cutting angle 1,5 °︱table width 530 mm︱back stop - adjustable 750 mm︱no. of strokes 29 Hub/min︱total power requirement 7,5 kW︱weight of the machine ca. 4100 kg︱dimensions of the machine ca. 3,63 x 2,20 x 1,28 m︱
          Description: The OSTAS machines are monobloc bodies made from quality ST42 material welded.The knives of the machine are made of 2379 quality, these high-quality knives guarantee precise and low-noise cutting. Furthermore, the machines work quietly thanks to their geared motor Braking system, the machines are also very energy-saving. basic equipment: - manual backgauge 600 mm - 1000 mm measuring stop with T-slot and stopper - Foot pedal with emergency stop button - Support arm in front for material - Cutting line lighting - Front and rear hand and foot protection - Piece counting counter Options: - engine. Behind stop with NC control and 750 mm adjustment - Pneumatic lifting device - Photoelectric barrier - Miter device with adjustable Angle 0-180º All other sizes at info@rs-sperling .de
            sheet width 3050 mm
            plate thickness 4 mm
            cutting angle 1,5 °
            table width 530 mm
            back stop - adjustable 750 mm
            no. of strokes 29 Hub/min
            total power requirement 7,5 kW
            weight of the machine ca. 4100 kg
            dimensions of the machine ca. 3,63 x 2,20 x 1,28 m
            Description :
            Description:
            The OSTAS machines are monobloc bodies made from quality ST42 material
            welded.The knives of the machine are made of 2379 quality, these
            high-quality knives guarantee precise and low-noise cutting.
            Furthermore, the machines work quietly thanks to their geared motor
            Braking system, the machines are also very energy-saving.

            basic equipment:
            - manual backgauge 600 mm
            - 1000 mm measuring stop with T-slot and stopper
            - Foot pedal with emergency stop button
            - Support arm in front for material
            - Cutting line lighting
            - Front and rear hand and foot protection
            - Piece counting counter

            Options:
            - engine. Behind stop with NC control and 750 mm adjustment
            - Pneumatic lifting device
            - Photoelectric barrier
            - Miter device with adjustable
            Angle 0-180º

            All other sizes at info@rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 2050 x 4


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091076 · Plate Shear - Mechanical

          OSTAS - ORGM 2050 x 4 - - 2023 -

          Technical details
          sheet width 2050 mm︱plate thickness 4 mm︱cutting angle 2,5 °︱table-size 530 x 830 mm︱table height 830 mm︱back stop - adjustable 750 mm︱no. of strokes 29 Hub/min︱total power requirement 7,5 kW︱weight of the machine ca. 1600 kg︱dimensions of the machine ca. 2,63 x 2,20 x 1,28 m︱
          Description: The OSTAS machines are monobloc bodies made from quality ST42 material welded.The knives of the machine are made of 2379 quality, these high-quality knives guarantee precise and low-noise cutting. Furthermore, the machines work quietly thanks to their geared motor Braking system, the machines are also very energy-saving. basic equipment: - engine. Behind stop with NC control and 750 mm adjustment - 1000 mm measuring stop with T-slot and stopper - Foot pedal with emergency stop button - Support arm in front for material - Cutting line lighting - Front and rear hand and foot protection - Piece counting counter Options: - Pneumatic lifting device - Photoelectric barrier - Miter device with adjustable Angle 0-180º All other sizes at info@rs-sperling .de
            sheet width 2050 mm
            plate thickness 4 mm
            cutting angle 2,5 °
            table-size 530 x 830 mm
            table height 830 mm
            back stop - adjustable 750 mm
            no. of strokes 29 Hub/min
            total power requirement 7,5 kW
            weight of the machine ca. 1600 kg
            dimensions of the machine ca. 2,63 x 2,20 x 1,28 m
            Description :
            Description:
            The OSTAS machines are monobloc bodies made from quality ST42 material
            welded.The knives of the machine are made of 2379 quality, these
            high-quality knives guarantee precise and low-noise cutting.
            Furthermore, the machines work quietly thanks to their geared motor
            Braking system, the machines are also very energy-saving.

            basic equipment:
            - engine. Behind stop with NC control and 750 mm adjustment
            - 1000 mm measuring stop with T-slot and stopper
            - Foot pedal with emergency stop button
            - Support arm in front for material
            - Cutting line lighting
            - Front and rear hand and foot protection
            - Piece counting counter

            Options:
            - Pneumatic lifting device
            - Photoelectric barrier
            - Miter device with adjustable
            Angle 0-180º

            All other sizes at info@rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 1050 x 4


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091072 · Plate Shear - Mechanical

          OSTAS - ORGM 1050 x 4 - - 2023 -

          Technical details
          sheet width 1.050 mm︱plate thickness 4 mm︱cutting angle 2,5 °︱table width 510 mm︱table height 820 mm︱back stop - adjustable 600 mm︱no. of strokes 35 Hub/min︱total power requirement 3 kW︱weight of the machine ca. 1.100 kg︱dimensions of the machine ca. 2,06 x 1,64 x 1,21 m︱
          Description: The OSTAS machines are monobloc bodies made from quality ST42 material welded.The knives of the machine are made of 2379 quality, these high-quality knives guarantee precise and low-noise cutting. Furthermore, the machines work quietly thanks to their geared motor Braking system, the machines are also very energy-saving. basic equipment: - manual backgauge 600 mm - 1000 mm measuring stop with T-slot and stopper - Foot pedal with emergency stop button - Support arm in front for material - Cutting line lighting - Front and rear hand and foot protection - Piece counting counter Options: - engine. Behind stop with NC control and 750 mm adjustment - Pneumatic lifting device - Photoelectric barrier - Miter device with adjustable Angle 0-180º All other sizes at info@rs-sperling .de
            sheet width 1.050 mm
            plate thickness 4 mm
            cutting angle 2,5 °
            table width 510 mm
            table height 820 mm
            back stop - adjustable 600 mm
            no. of strokes 35 Hub/min
            total power requirement 3 kW
            weight of the machine ca. 1.100 kg
            dimensions of the machine ca. 2,06 x 1,64 x 1,21 m
            Description :
            Description:
            The OSTAS machines are monobloc bodies made from quality ST42 material
            welded.The knives of the machine are made of 2379 quality, these
            high-quality knives guarantee precise and low-noise cutting.
            Furthermore, the machines work quietly thanks to their geared motor
            Braking system, the machines are also very energy-saving.

            basic equipment:
            - manual backgauge 600 mm
            - 1000 mm measuring stop with T-slot and stopper
            - Foot pedal with emergency stop button
            - Support arm in front for material
            - Cutting line lighting
            - Front and rear hand and foot protection
            - Piece counting counter

            Options:
            - engine. Behind stop with NC control and 750 mm adjustment
            - Pneumatic lifting device
            - Photoelectric barrier
            - Miter device with adjustable
            Angle 0-180º

            All other sizes at info@rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 3050 x 3


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091069 · Plate Shear - Mechanical

          OSTAS - ORGM 3050 x 3 - - 2023 -

          Technical details
          sheet width 3050 mm︱plate thickness 3,0 mm︱cutting angle 1,5 °︱table width 530 mm︱table height 820 mm︱back stop - adjustable 600 mm︱no. of strokes 35 Hub/min︱total power requirement 4 kW︱weight of the machine ca. 2300 kg︱dimensions of the machine ca. 3,64 x 2,06 x 1,21 m︱
          Basic equipment: - manual backgauge with 600 mm travel - Measuring stop 800 mm - Foot pedal with emergency stop switch - Bracket arms in front for workpieces - Cutting line lighting - Protective demarcation OPTIONS: - Pneumatic sheet metal lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° - engine. Backgauge with NC control and 750 mm travel - engine. Backgauge with NC control and 1000 mm travel - piece counter More sizes at info @ rs-sperling .de
            sheet width 3050 mm
            plate thickness 3,0 mm
            cutting angle 1,5 °
            table width 530 mm
            table height 820 mm
            back stop - adjustable 600 mm
            no. of strokes 35 Hub/min
            total power requirement 4 kW
            weight of the machine ca. 2300 kg
            dimensions of the machine ca. 3,64 x 2,06 x 1,21 m
            Description :
            Basic equipment:
            - manual backgauge with 600 mm travel
            - Measuring stop 800 mm
            - Foot pedal with emergency stop switch
            - Bracket arms in front for workpieces
            - Cutting line lighting
            - Protective demarcation

            OPTIONS:
            - Pneumatic sheet metal lifting device
            - Optical safety bar
            - Miter device with adjustable
            - angle 0-180 °
            - engine. Backgauge with NC control
            and 750 mm travel
            - engine. Backgauge with NC control
            and 1000 mm travel
            - piece counter

            More sizes at info @ rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical VOLZ EuroCut 2040


          • Volz Werkzeugmaschinen
          • Friedrich-Ebert Straße 78-80
          • 58454 Witten-Annen
          • Deutschland

          • +49 (0) 23 02 / 98 72 – 0
            +49 (0) 23 02 / 98 72 - 50
          • anfrage@volz-witten.de
            www.volz-witten.de
          #1134-110001 · Plate Shear - Mechanical

          VOLZ - EuroCut 2040 - - 2023 -

          Technical details
          sheet width 2060 mm︱plate thickness 04,0 mm︱distance between columns mm︱table width 455 mm︱work height max. 880 mm︱
            sheet width 2060 mm
            plate thickness 04,0 mm
            table width 455 mm
            work height max. 880 mm


        • Volz Werkzeugmaschinen
        • Friedrich-Ebert Straße 78-80
        • 58454 Witten-Annen
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 1350 x 6


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091086 · Plate Shear - Mechanical

          OSTAS - ORGM 1350 x 6 - - 2023 -

          Technical details
          sheet width 1350 mm︱plate thickness 6 mm︱cutting angle 2,5 °︱table width 530 mm︱table height 830 mm︱back stop - adjustable 750 mm︱no. of strokes 29 Hub/min︱total power requirement 7,5 kW︱weight of the machine ca. 2150 kg︱dimensions of the machine ca. 2,2 x 1,93 x 1,28 m︱
          Description: The OSTAS machines are monobloc bodies made from quality ST42 material welded.The knives of the machine are made of 2379 quality, these high-quality knives guarantee precise and low-noise cutting. Furthermore, the machines work quietly thanks to their geared motor Braking system, the machines are also very energy-saving. basic equipment: - manual backgauge 600 mm - 1000 mm measuring stop with T-slot and stopper - Foot pedal with emergency stop button - Support arm in front for material - Cutting line lighting - Front and rear hand and foot protection - Piece counting counter Options: - engine. Behind stop with NC control and 750 mm adjustment - Pneumatic lifting device - Photoelectric barrier - Miter device with adjustable Angle 0-180º All other sizes at info@rs-sperling .de
            sheet width 1350 mm
            plate thickness 6 mm
            cutting angle 2,5 °
            table width 530 mm
            table height 830 mm
            back stop - adjustable 750 mm
            no. of strokes 29 Hub/min
            total power requirement 7,5 kW
            weight of the machine ca. 2150 kg
            dimensions of the machine ca. 2,2 x 1,93 x 1,28 m
            Description :
            Description:
            The OSTAS machines are monobloc bodies made from quality ST42 material
            welded.The knives of the machine are made of 2379 quality, these
            high-quality knives guarantee precise and low-noise cutting.
            Furthermore, the machines work quietly thanks to their geared motor
            Braking system, the machines are also very energy-saving.

            basic equipment:
            - manual backgauge 600 mm
            - 1000 mm measuring stop with T-slot and stopper
            - Foot pedal with emergency stop button
            - Support arm in front for material
            - Cutting line lighting
            - Front and rear hand and foot protection
            - Piece counting counter

            Options:
            - engine. Behind stop with NC control and 750 mm adjustment
            - Pneumatic lifting device
            - Photoelectric barrier
            - Miter device with adjustable
            Angle 0-180º

            All other sizes at info@rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 1550 x 6


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091089 · Plate Shear - Mechanical

          OSTAS - ORGM 1550 x 6 - - 2023 -

          Technical details
          sheet width 1550 mm︱plate thickness 6 mm︱cutting angle 2,5 °︱table width 510 mm︱table height 830 mm︱back stop - adjustable 750 mm︱no. of strokes 29 Hub/min︱total power requirement 7,5 kW︱weight of the machine ca. 2,5 t︱dimensions of the machine ca. 2,1 x 2,2 x 1,28 mm︱
          Description: The OSTAS machines are monobloc bodies made from quality ST42 material welded.The knives of the machine are made of 2379 quality, these high-quality knives guarantee precise and low-noise cutting. Furthermore, the machines work quietly thanks to their geared motor Braking system, the machines are also very energy-saving. basic equipment: - manual backgauge 600 mm - 1000 mm measuring stop with T-slot and stopper - Foot pedal with emergency stop button - Support arm in front for material - Cutting line lighting - Front and rear hand and foot protection - Piece counting counter Options: - engine. Behind stop with NC control and 750 mm adjustment - Pneumatic lifting device - Photoelectric barrier - Miter device with adjustable Angle 0-180º All other sizes at info@rs-sperling .de
            sheet width 1550 mm
            plate thickness 6 mm
            cutting angle 2,5 °
            table width 510 mm
            table height 830 mm
            back stop - adjustable 750 mm
            no. of strokes 29 Hub/min
            total power requirement 7,5 kW
            weight of the machine ca. 2,5 t
            dimensions of the machine ca. 2,1 x 2,2 x 1,28 mm
            Description :
            Description:
            The OSTAS machines are monobloc bodies made from quality ST42 material
            welded.The knives of the machine are made of 2379 quality, these
            high-quality knives guarantee precise and low-noise cutting.
            Furthermore, the machines work quietly thanks to their geared motor
            Braking system, the machines are also very energy-saving.

            basic equipment:
            - manual backgauge 600 mm
            - 1000 mm measuring stop with T-slot and stopper
            - Foot pedal with emergency stop button
            - Support arm in front for material
            - Cutting line lighting
            - Front and rear hand and foot protection
            - Piece counting counter

            Options:
            - engine. Behind stop with NC control and 750 mm adjustment
            - Pneumatic lifting device
            - Photoelectric barrier
            - Miter device with adjustable
            Angle 0-180º

            All other sizes at info@rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 1550 x 3


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091060 · Plate Shear - Mechanical

          OSTAS - ORGM 1550 x 3 - - 2023 -

          Technical details
          sheet width 1.550 mm︱plate thickness 3 mm︱cutting angle 2,5 °︱table width 510 mm︱table height 820 mm︱back stop - adjustable 600 mm︱no. of strokes 35 Hub/min︱total power requirement 3 kW︱weight of the machine ca. 1600 kg︱dimensions of the machine ca. 2,14 x 2,06 x 1,21 m︱
          Basic equipment: - engine. Backgauge with NC control and 750 mm travel - Measuring stop 800 mm - Foot pedal with emergency stop switch - Bracket arms in front for workpieces - Cutting line lighting - Protective demarcation OPTIONS: - Pneumatic sheet metal lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° - engine. Backgauge with NC control and 1000 mm travel - piece counter All other sizes can be found on the RS-Sperling Website.
            sheet width 1.550 mm
            plate thickness 3 mm
            cutting angle 2,5 °
            table width 510 mm
            table height 820 mm
            back stop - adjustable 600 mm
            no. of strokes 35 Hub/min
            total power requirement 3 kW
            weight of the machine ca. 1600 kg
            dimensions of the machine ca. 2,14 x 2,06 x 1,21 m
            Description :
            Basic equipment:
            - engine. Backgauge with NC control
            and 750 mm travel
            - Measuring stop 800 mm
            - Foot pedal with emergency stop switch
            - Bracket arms in front for workpieces
            - Cutting line lighting
            - Protective demarcation

            OPTIONS:
            - Pneumatic sheet metal lifting device
            - Optical safety bar
            - Miter device with adjustable
            - angle 0-180 °
            - engine. Backgauge with NC control
            and 1000 mm travel
            - piece counter

            All other sizes can be found on the RS-Sperling
            Website.


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 1350 x 3


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091058 · Plate Shear - Mechanical

          OSTAS - ORGM 1350 x 3 - - 2023 -

          Technical details
          sheet width 1.350 mm︱plate thickness 3 mm︱cutting angle 2,5 °︱table width 510 mm︱table height 820 mm︱back stop - adjustable 600 mm︱no. of strokes 35 Hub/min︱total power requirement 3 kW︱weight of the machine ca. 1350 kg︱dimensions of the machine ca. 2,6 x 1,94 x 1,21 m︱
          Basic equipment: - manual backgauge with 600 mm travel - Measuring stop 800 mm - Foot pedal with emergency stop switch - Bracket arms in front for workpieces - Cutting line lighting - Protective demarcation OPTIONS: - Pneumatic sheet metal lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° - engine. Backgauge with NC control and 750 mm travel - engine. Backgauge with NC control and 1000 mm travel - piece counter More sizes at info @ rs-sperling .de
            sheet width 1.350 mm
            plate thickness 3 mm
            cutting angle 2,5 °
            table width 510 mm
            table height 820 mm
            back stop - adjustable 600 mm
            no. of strokes 35 Hub/min
            total power requirement 3 kW
            weight of the machine ca. 1350 kg
            dimensions of the machine ca. 2,6 x 1,94 x 1,21 m
            Description :
            Basic equipment:
            - manual backgauge with 600 mm travel
            - Measuring stop 800 mm
            - Foot pedal with emergency stop switch
            - Bracket arms in front for workpieces
            - Cutting line lighting
            - Protective demarcation

            OPTIONS:
            - Pneumatic sheet metal lifting device
            - Optical safety bar
            - Miter device with adjustable
            - angle 0-180 °
            - engine. Backgauge with NC control
            and 750 mm travel
            - engine. Backgauge with NC control
            and 1000 mm travel
            - piece counter

            More sizes at info @ rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 1050 x 3


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091055 · Plate Shear - Mechanical

          OSTAS - ORGM 1050 x 3 - - 2023 -

          Technical details
          sheet width 1.050 mm︱plate thickness 3 mm︱cutting angle 2,5 °︱table width 510 mm︱table height 820 mm︱back stop - adjustable 600 mm︱no. of strokes 35 Hub/min︱total power requirement 3 kW︱weight of the machine ca. 1.100 kg︱dimensions of the machine ca. 2,06 x 1,64 x 1,21 m︱
          Basic equipment: - manual backgauge with 600 mm travel - Measuring stop 800 mm - Foot pedal with emergency stop switch - Bracket arms in front for workpieces - Cutting line lighting - Protective demarcation OPTIONS: - Pneumatic sheet metal lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° - engine. Backgauge with NC control and 750 mm travel - engine. Backgauge with NC control and 1000 mm travel - piece counter More sizes at info @ rs-sperling .de
            sheet width 1.050 mm
            plate thickness 3 mm
            cutting angle 2,5 °
            table width 510 mm
            table height 820 mm
            back stop - adjustable 600 mm
            no. of strokes 35 Hub/min
            total power requirement 3 kW
            weight of the machine ca. 1.100 kg
            dimensions of the machine ca. 2,06 x 1,64 x 1,21 m
            Description :
            Basic equipment:
            - manual backgauge with 600 mm travel
            - Measuring stop 800 mm
            - Foot pedal with emergency stop switch
            - Bracket arms in front for workpieces
            - Cutting line lighting
            - Protective demarcation

            OPTIONS:
            - Pneumatic sheet metal lifting device
            - Optical safety bar
            - Miter device with adjustable
            - angle 0-180 °
            - engine. Backgauge with NC control
            and 750 mm travel
            - engine. Backgauge with NC control
            and 1000 mm travel
            - piece counter

            More sizes at info @ rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 2050 x 6


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091092 · Plate Shear - Mechanical

          OSTAS - ORGM 2050 x 6 - - 2023 -

          Technical details
          sheet width 2050 mm︱plate thickness 6 mm︱cutting angle 1,5 °︱table width 530 mm︱table height 830 mm︱back stop - adjustable 750 mm︱no. of strokes 29 Hub/min︱total power requirement 7,7 kW︱weight of the machine ca. 3100 kg︱dimensions of the machine ca. 2,2 x 2,63 x 1,28 mm︱
          Description: The OSTAS machines are monobloc bodies made from quality ST42 material welded.The knives of the machine are made of 2379 quality, these high-quality knives guarantee precise and low-noise cutting. Furthermore, the machines work quietly thanks to their geared motor Braking system, the machines are also very energy-saving. basic equipment: - manual backgauge 600 mm - 1000 mm measuring stop with T-slot and stopper - Foot pedal with emergency stop button - Support arm in front for material - Cutting line lighting - Front and rear hand and foot protection - Piece counting counter Options: - engine. Behind stop with NC control and 750 mm adjustment - Pneumatic lifting device - Photoelectric barrier - Miter device with adjustable Angle 0-180º All other sizes at info@rs-sperling .de
            sheet width 2050 mm
            plate thickness 6 mm
            cutting angle 1,5 °
            table width 530 mm
            table height 830 mm
            back stop - adjustable 750 mm
            no. of strokes 29 Hub/min
            total power requirement 7,7 kW
            weight of the machine ca. 3100 kg
            dimensions of the machine ca. 2,2 x 2,63 x 1,28 mm
            Description :
            Description:
            The OSTAS machines are monobloc bodies made from quality ST42 material
            welded.The knives of the machine are made of 2379 quality, these
            high-quality knives guarantee precise and low-noise cutting.
            Furthermore, the machines work quietly thanks to their geared motor
            Braking system, the machines are also very energy-saving.

            basic equipment:
            - manual backgauge 600 mm
            - 1000 mm measuring stop with T-slot and stopper
            - Foot pedal with emergency stop button
            - Support arm in front for material
            - Cutting line lighting
            - Front and rear hand and foot protection
            - Piece counting counter

            Options:
            - engine. Behind stop with NC control and 750 mm adjustment
            - Pneumatic lifting device
            - Photoelectric barrier
            - Miter device with adjustable
            Angle 0-180º

            All other sizes at info@rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 1550 x 5


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091073 · Plate Shear - Mechanical

          OSTAS - ORGM 1550 x 5 - - 2023 -

          Technical details
          sheet width 1550 mm︱plate thickness 5 mm︱cutting angle 2,5 °︱table width 530 mm︱table height 830 mm︱back stop - adjustable 750 mm︱no. of strokes 29 Hub/min︱total power requirement 7,5 kW︱weight of the machine ca. 1350 kg︱dimensions of the machine ca. 2,13 x 2,20 x 1,28 m︱
          Description: The OSTAS machines are monobloc bodies made from quality ST42 material welded.The knives of the machine are made of 2379 quality, these high-quality knives guarantee precise and low-noise cutting. Furthermore, the machines work quietly thanks to their geared motor Braking system, the machines are also very energy-saving. basic equipment: - manual backgauge 600 mm - 1000 mm measuring stop with T-slot and stopper - Foot pedal with emergency stop button - Support arm in front for material - Cutting line lighting - Front and rear hand and foot protection - Piece counting counter Options: - engine. Behind stop with NC control and 750 mm adjustment - Pneumatic lifting device - Photoelectric barrier - Miter device with adjustable Angle 0-180º All other sizes at info@rs-sperling .de
            sheet width 1550 mm
            plate thickness 5 mm
            cutting angle 2,5 °
            table width 530 mm
            table height 830 mm
            back stop - adjustable 750 mm
            no. of strokes 29 Hub/min
            total power requirement 7,5 kW
            weight of the machine ca. 1350 kg
            dimensions of the machine ca. 2,13 x 2,20 x 1,28 m
            Description :
            Description:
            The OSTAS machines are monobloc bodies made from quality ST42 material
            welded.The knives of the machine are made of 2379 quality, these
            high-quality knives guarantee precise and low-noise cutting.
            Furthermore, the machines work quietly thanks to their geared motor
            Braking system, the machines are also very energy-saving.

            basic equipment:
            - manual backgauge 600 mm
            - 1000 mm measuring stop with T-slot and stopper
            - Foot pedal with emergency stop button
            - Support arm in front for material
            - Cutting line lighting
            - Front and rear hand and foot protection
            - Piece counting counter

            Options:
            - engine. Behind stop with NC control and 750 mm adjustment
            - Pneumatic lifting device
            - Photoelectric barrier
            - Miter device with adjustable
            Angle 0-180º

            All other sizes at info@rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 2050 x 3


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091063 · Plate Shear - Mechanical

          OSTAS - ORGM 2050 x 3 - - 2023 -

          Technical details
          sheet width 2050 mm︱plate thickness 3 mm︱cutting angle 1,5 °︱table width 510 mm︱table height 820 mm︱back stop - adjustable 600 mm︱no. of strokes 35 Hub/min︱total power requirement 3 kW︱weight of the machine ca. 1900 kg︱dimensions of the machine ca. 2,64 x 2,06 x 1,21 m︱
          Basic equipment: - engine. Backgauge with NC control and 750 mm travel - Measuring stop 800 mm - Foot pedal with emergency stop switch - Bracket arms in front for workpieces - Cutting line lighting - Protective demarcation OPTIONS: - Pneumatic sheet metal lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° - engine. Backgauge with NC control and 1000 mm travel - piece counter More sizes at info @ rs-sperling .de
            sheet width 2050 mm
            plate thickness 3 mm
            cutting angle 1,5 °
            table width 510 mm
            table height 820 mm
            back stop - adjustable 600 mm
            no. of strokes 35 Hub/min
            total power requirement 3 kW
            weight of the machine ca. 1900 kg
            dimensions of the machine ca. 2,64 x 2,06 x 1,21 m
            Description :
            Basic equipment:
            - engine. Backgauge with NC control
            and 750 mm travel
            - Measuring stop 800 mm
            - Foot pedal with emergency stop switch
            - Bracket arms in front for workpieces
            - Cutting line lighting
            - Protective demarcation

            OPTIONS:
            - Pneumatic sheet metal lifting device
            - Optical safety bar
            - Miter device with adjustable
            - angle 0-180 °
            - engine. Backgauge with NC control
            and 1000 mm travel
            - piece counter

            More sizes at info @ rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 1050 x 6


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091084 · Plate Shear - Mechanical

          OSTAS - ORGM 1050 x 6 - - 2023 -

          Technical details
          sheet width 1050 mm︱plate thickness 6 mm︱cutting angle 2,5 °︱table width 530 mm︱table height 830 mm︱back stop - adjustable 750 mm︱no. of strokes 29 Hub/min︱total power requirement 7,5 kW︱weight of the machine ca. 1800 kg︱dimensions of the machine ca. 1,35 x 2,20 x 1,28 m︱
          Description: The OSTAS machines are monobloc bodies made from quality ST42 material welded.The knives of the machine are made of 2379 quality, these high-quality knives guarantee precise and low-noise cutting. Furthermore, the machines work quietly thanks to their geared motor Braking system, the machines are also very energy-saving. basic equipment: - engine. Behind stop with NC control and 750 mm adjustment - 1000 mm measuring stop with T-slot and stopper - Foot pedal with emergency stop button - Support arm in front for material - Cutting line lighting - Front and rear hand and foot protection - Piece counting counter Options: - Pneumatic lifting device - Photoelectric barrier - Miter device with adjustable Angle 0-180º All other sizes at info@rs-sperling .de
            sheet width 1050 mm
            plate thickness 6 mm
            cutting angle 2,5 °
            table width 530 mm
            table height 830 mm
            back stop - adjustable 750 mm
            no. of strokes 29 Hub/min
            total power requirement 7,5 kW
            weight of the machine ca. 1800 kg
            dimensions of the machine ca. 1,35 x 2,20 x 1,28 m
            Description :
            Description:
            The OSTAS machines are monobloc bodies made from quality ST42 material
            welded.The knives of the machine are made of 2379 quality, these
            high-quality knives guarantee precise and low-noise cutting.
            Furthermore, the machines work quietly thanks to their geared motor
            Braking system, the machines are also very energy-saving.

            basic equipment:
            - engine. Behind stop with NC control and 750 mm adjustment
            - 1000 mm measuring stop with T-slot and stopper
            - Foot pedal with emergency stop button
            - Support arm in front for material
            - Cutting line lighting
            - Front and rear hand and foot protection
            - Piece counting counter

            Options:
            - Pneumatic lifting device
            - Photoelectric barrier
            - Miter device with adjustable
            Angle 0-180º

            All other sizes at info@rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 1350 x 5


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091070 · Plate Shear - Mechanical

          OSTAS - ORGM 1350 x 5 - - 2023 -

          Technical details
          sheet width 1350 mm︱plate thickness 5 mm︱cutting angle 2,3 °︱table width 530 mm︱table height 830 mm︱back stop - adjustable 750 mm︱no. of strokes 29 Hub/min︱total power requirement 7,5 kW︱weight of the machine ca. 1100 kg︱dimensions of the machine ca. 1,93 x 2,2 x 1,28 m︱
          Description: The OSTAS machines are monobloc bodies made from quality ST42 material welded.The knives of the machine are made of 2379 quality, these high-quality knives guarantee precise and low-noise cutting. Furthermore, the machines work quietly thanks to their geared motor Braking system, the machines are also very energy-saving. basic equipment: - manual backgauge 600 mm - 1000 mm measuring stop with T-slot and stopper - Foot pedal with emergency stop button - Support arm in front for material - Cutting line lighting - Front and rear hand and foot protection - Piece counting counter Options: - engine. Behind stop with NC control and 750 mm adjustment - Pneumatic lifting device - Photoelectric barrier - Miter device with adjustable Angle 0-180º All other sizes at info@rs-sperling .de
            sheet width 1350 mm
            plate thickness 5 mm
            cutting angle 2,3 °
            table width 530 mm
            table height 830 mm
            back stop - adjustable 750 mm
            no. of strokes 29 Hub/min
            total power requirement 7,5 kW
            weight of the machine ca. 1100 kg
            dimensions of the machine ca. 1,93 x 2,2 x 1,28 m
            Description :
            Description:
            The OSTAS machines are monobloc bodies made from quality ST42 material
            welded.The knives of the machine are made of 2379 quality, these
            high-quality knives guarantee precise and low-noise cutting.
            Furthermore, the machines work quietly thanks to their geared motor
            Braking system, the machines are also very energy-saving.

            basic equipment:
            - manual backgauge 600 mm
            - 1000 mm measuring stop with T-slot and stopper
            - Foot pedal with emergency stop button
            - Support arm in front for material
            - Cutting line lighting
            - Front and rear hand and foot protection
            - Piece counting counter

            Options:
            - engine. Behind stop with NC control and 750 mm adjustment
            - Pneumatic lifting device
            - Photoelectric barrier
            - Miter device with adjustable
            Angle 0-180º

            All other sizes at info@rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical VOLZ EuroCut 3040


          • Volz Werkzeugmaschinen
          • Friedrich-Ebert Straße 78-80
          • 58454 Witten-Annen
          • Deutschland

          • +49 (0) 23 02 / 98 72 – 0
            +49 (0) 23 02 / 98 72 - 50
          • anfrage@volz-witten.de
            www.volz-witten.de
          #1134-110000 · Plate Shear - Mechanical

          VOLZ - EuroCut 3040 - - 2023 -

          Technical details
          sheet width 3060 mm︱plate thickness 04,0 mm︱distance between columns mm︱table width 455 mm︱work height max. 880 mm︱
            sheet width 3060 mm
            plate thickness 04,0 mm
            table width 455 mm
            work height max. 880 mm


        • Volz Werkzeugmaschinen
        • Friedrich-Ebert Straße 78-80
        • 58454 Witten-Annen
        • Deutschland

        • Datasheet
          Request / Contact
          used Sheet metal working / shaeres / bending Plate Shear - Mechanical OSTAS ORGM 2550 x 3


          • RS Sperling
          • von-Braun-Str. 20
          • 46244 Bottrop
          • Deutschland

          • +49 (0) 2045 / 41 43 22-0
            +49 (0) 2045 / 41 43 22-9
          • info@rs-sperling.de
            www.rs-sperling.de
          #1100-091065 · Plate Shear - Mechanical

          OSTAS - ORGM 2550 x 3 - - 2023 -

          Technical details
          sheet width 2550 mm︱plate thickness 3 mm︱cutting angle 1,5 °︱table width 510 mm︱table height 820 mm︱back stop - adjustable 600 mm︱no. of strokes 35 Hub/min︱total power requirement 3 kW︱weight of the machine ca. 2400 kg︱dimensions of the machine ca. 3,14 x 2,06 x 1,21 m︱
          Basic equipment: - manual backgauge with 600 mm travel - Measuring stop 800 mm - Foot pedal with emergency stop switch - Bracket arms in front for workpieces - Cutting line lighting - Protective demarcation OPTIONS: - Pneumatic sheet metal lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° - engine. Backgauge with NC control and 750 mm travel - engine. Backgauge with NC control and 1000 mm travel - piece counter More sizes at info @ rs-sperling .de
            sheet width 2550 mm
            plate thickness 3 mm
            cutting angle 1,5 °
            table width 510 mm
            table height 820 mm
            back stop - adjustable 600 mm
            no. of strokes 35 Hub/min
            total power requirement 3 kW
            weight of the machine ca. 2400 kg
            dimensions of the machine ca. 3,14 x 2,06 x 1,21 m
            Description :
            Basic equipment:
            - manual backgauge with 600 mm travel
            - Measuring stop 800 mm
            - Foot pedal with emergency stop switch
            - Bracket arms in front for workpieces
            - Cutting line lighting
            - Protective demarcation

            OPTIONS:
            - Pneumatic sheet metal lifting device
            - Optical safety bar
            - Miter device with adjustable
            - angle 0-180 °
            - engine. Backgauge with NC control
            and 750 mm travel
            - engine. Backgauge with NC control
            and 1000 mm travel
            - piece counter

            More sizes at info @ rs-sperling .de


        • RS Sperling
        • von-Braun-Str. 20
        • 46244 Bottrop
        • Deutschland

        • Datasheet
          Request / Contact
          •   
          •   
          • 1  
          • 2  
          • 3  
          • 4  
          • 5  
          •   
          •