Cut-to-length-lines
Machinelist: Cut-to-length-lines
Cut-to-length-lines
- SCHMITT REINHOLD GMBH
- Obernahmerstr. 74
- 58119 Hagen-Hohenlimburg
- Deutschland
-
+49 (0)2334 4847
+49 (0)2334 4840 -
info@reinhold-schmitt.de
www.reinhold-schmitt.de
#2008-056810 · Cut-to-length-lines
VIGANO/RIVA - - - 2000/2001 -
Technical details
sheet length 580 - 6.000 mm working direction left - right otherwise according to technical specification 05.68-1.0
Datasheet
Request / Contact
- Kemmerich Werkzeugmaschinen
- Im Rottfeld 1a
- 40789 Monheim am Rhein
- Deutschland
-
+49 2173 207474
+49 2173 207473 -
info@kemmerich.biz
www.kemmerich.biz
#1020-19439 · Cut-to-length-lines
HITACHI - - - 1993 -
Technical details
Stainless steel Cut to Length Line(Flying type) - Material: stainless steel, surface treated steel -- Thickness: 0.3–3 mm (as of stainless steel) -- Width: 500-1350 mm -- Trim: 5-25 mm on one side (more than twice the plate thickness) - Material coil: internal diameter 508 mm, external diameter 600–1800 mm -- weight maximum 15 tons -- Width accuracy: 500–1350 mm plus or minus 0.2 mm (when side trimming) -- Product length: 400–6000 mm Plus/minus 0.3 mm - 6-leveler (6-hi) leveler x 2units types -- Tension: 45 to 50 kg/mm2 -- Yield point: 28 kg/mm2 - Cutting method: Cut while running (flying), numerically controlled rocking type - flying shears -- (Cutting speed) 20–40/80 m/min -- Speed 2-speed change type --- 0.3 to 1.2 mm: 20 to 80 m/min --- 0.21–3 mm: 20–40 m/min -- Slow operation: 0.8 m/min -- Conveyor speed: 20~120m/min -- Cut count: up to 150 cuts/min -- (Product piling) --- Plate width: 500–1350 mm --- No1 piler: 400 to 3100 mm (also used as a reject filer) --- No2 piler: 400–6100 mm --- Load height: up to 600mm --- Load weight: up to 4 tons Line direction: From right to left on control panel Line: Approximately 13 m x 49.050 m (Major facilities) - Coil skid - Coil car - Pay off reel and a paper winder - Coil opener - Rough Leveler - Shear - No. 1 Looper Guide - Side guide and pinch roller - Side trimmer - Scrap winder x2 - No.1 Finisher Leveler (6-hi) - No2 Finisher Leveler (6-hi) - No 2 Looper Guide - Measuring roller, feed roller and paper-off reel - Shear - Conveyor - Cart - No1/No2 piler type - Hydraulic unit: Type - Valve stand type - (Coil skid) -- V-type fixed skid -- Coil maintenance: 1 coil -- Coil weight: up to 15 tonnes -- Coil diameter: 600 to 1800 mm -urethane rubber (Coil Car) Cradle roller type Hydraulic boost Electricity transfer driving type Two guide lots hydraulic cylinder elevating type (payoff reel and paper winder) Overhang, single-mant 4-segment type Paper reel motor: DC 5.5KW 400/1600 RPM, attached to brake Paper winder: cone type, (motor DC 1.5KW, 1750 RPM) (Coil Opener) Knife edge method (Rough Leveler) 2-stage (2hi) 5-body roller leveler Pinch rollers: 160 mm × 1450 mm 2 pieces, The upper part of the pinch roller is hydraulic cylinder press-down, and the lower roller is fixed 5 workload rollers 130mm x 1450mm The upper roller of the workload roller is electrically pressed, and the lower roller is fixed 0–40/80 m/min Two-stage change 0.3 to 1.6 mmt: 80 m/min 1.7 to 1.6 mmt: 40 m/min Motor: DC 18.5 KW, 1750 RPM, Brake Attachment Pressing motor: 2 1.5KW 100RPMs with brakes (Shear) Hydraulic up cut shear Knife size: 25 mm thickness × 150 mm width × 1450 mm length (No. 1 Looper Guide) Table lift Hydraulic cylinder operation method Loop: Light Volume Control Method Roller: 70 mm diameter × 1450 mm × 6 bonds, rubber lining roller (Side guide and pinch roller) Vertical Free Roller Electrically switched type Side guide roller: 90 mm diameter × 150 mm length × 6 bones Pinch Roller: 2nd Stage (2hi) Roller: 160 mm diameter × 1450 mm length × 2 bones Upper roller: pneumatic cylinder pressure free roller Lower Roller: Fixed Drive Roller (Side trimmer) Overhang Drive Cut 0–40/80 m/min 2-stage change type 0.3 to 1.6 mmt: 80 m/min 1.7 to 1.6 mmt: 40 m/min Cutter diameter: 320 mm / 190 mm internal diameter × 20 mm thickness Roller: 320 mm external diameter × 19 mm internal diameter × 20 mm thickness Motor: DC 5.5KW 1750RPM (Scrap winder) Two machines Link Pin Gauge Type (Hydraulic Cylinder Opening and Closing Type) Motor: 2 DC 2.2KW 1450 RPM (No1 Finisher Leveler) 6-level (6-hi) 17 leveler Thickness: 1.21–3.0 mm Speed: 6 to 40/80 m/min Thickness 0.3–1.2 mm 6–80 m/min Thickness 1.21–3 mm 6–40 m/min Pinch roller: 180 mm × 1750 mm × 2 bones The upper roll is a pneumatic cylinder. The lower roll is fixed Rubber lining drive roller Work roll: 60mm x 1750mm x 17e 8 for the upper roll, 9 for the lower roll Plated abrasive roller Medium roller: 50 mm × 1750 mm × 19 pieces 9 for the upper roll, 10 for the bottom roll Backup Roller: 88 mm Diameter x 50 mm Length x 7 rows Pressing Method: Lower Roller Parallel Pressing Pressing speed: 0.25 mm/sec Pressurization: plus or minus 5 mm Motor: DC 55KW 1750 RPM Brake Attachment (No2 Finisher Leveler) 6-level (6-hi) 17 leveler Plate thickness: 0.3–1.2 mm Speed: 5 to 80 m/min Pinch roller: 180 mm × 1750 mm × 2 bones The upper roll is a pneumatic cylinder. The lower roll is fixed Rubber lining drive roller Work roll: 35mm x 1750mm x 17bon 8 for the upper roll, 9 for the lower roll Plated abrasive roller Medium Roller: 32 mm × 1750 mm × 19 pieces 9 for the upper roll, 10 for the bottom roll Backup Roller: 99 mm Diameter x 50 mm Length x 7 rows Roller bearing type Pressing Method: Lower Roller Parallel Pressing Pressing speed: 0.25 mm/sec Pressurization: plus or minus 5 mm Motor: DC 35KW 1750RPM Brake Attachment (No. 2 Looper Guide) Table lift Hydraulic cylinder operation method Loop: How to control the amount of light (amount of light) Roller: 70 mm diameter × 1450 mm × 6 bonds, rubber lining roller (Measuring roll/feed roller/paper vinyl payoff reel) Measuring roller: The upper roll is pneumatic pressing, the lower roll is fixed, the pressing amount is 30 mm Feed roller: Upper roll is pneumatic cylinder press, lower roll is fixed, press load is 40 mm Motor: DC 2.2KW 1750RPM (Shear) Fluctuating Flying shear 0.3~3mm Speed: 2 groups of 20–40/80 m/min Thickness 0.3–1.6 mm 80 m/min Tlate thickness 1.6–3 mm 40 m/min Cut count: up to 150 cuts/min Cutting length: 400–6000 mm Electric up CUT shear Cut up and down knife die via motor, reducer, pinion stand crankshaft Knife: 20 mmt × 80 mm × 1400 mm × 1 set The top knife is a straight knife, and the bottom is a V-lock knife Adjustment: Wedge Motor: DC 75KW 550RPM (Conveyor) Belt conveyor type Belt width: 1200 mm Conveyor length: 3800 mm Motor DC 5.5KW 1450RPM Brake Attachment (No. 1 No. 2 piler) No1 piler: Combined use of reject truck, air blower Combined use of side conveyor No2 piler: Combined suction conveyor and air blower Loading height: 600 mm Lift: Hydraulic lift volume 650 mm Motor: 4 1.5KW 150RPM units for side guide end stoppers 2.2 KW 1500RPM for lifters 1.5KW for cart 7.5KW for blower (Hydraulic device) 70 kg/cm2 × 100 L/min Pen pump Motor: DC 18.5 KW 1000 RPM (Supply power) AC400 V,50 Hertz 3 Phase / AC200 V,50 Hertz 3 Phase (Control power) AC 200V, 50 Hz Single Phase (Compressed air) Compressed air required: 5 kg/cm2
Datasheet
Request / Contact
- SCHMITT REINHOLD GMBH
- Obernahmerstr. 74
- 58119 Hagen-Hohenlimburg
- Deutschland
-
+49 (0)2334 4847
+49 (0)2334 4840 -
info@reinhold-schmitt.de
www.reinhold-schmitt.de
#2008-056410 · Cut-to-length-lines
WILHELMSBURGER - - - 1975 -
Technical details
length tolerance ± 0,5 mm width tolerance ± 0,5 mm diagonal tolerance ± 1,0 mm line consisting of: double side decoiler leveler no. of leveling rolls 21 leveling roll diameter 35 mm flying shear magnetic conveyor table - length 10 m 2 output tables electric pneumatic hydraulic
Datasheet
Request / Contact
- Jansen Machinehandel BV
- Bredaseweg 210
- 4873 LA Etten-leur
- Nederland
-
+31 (0) 76 5015750
-
info@jansenmachinehandel.nl
www.jansenmachinehandel.nl
#2049-M825 · Cut-to-length-lines
Hydro Meca - 90L4C108H - - -
Technical details
Pipe cutting machine
Plate Bending Machine - 3 Rolls
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-226 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - R 1050 x 75 - - 2021 -
Technical details
MINT CONDITION 3 rolls asymmetric rolls - prebending longitudinal grooves in lower and lateral roll Infeed of the lower roller by a central lever - with gear reduction machine stand user manual in GERMAN orENGLISH
Datasheet
Request / Contact
- Kurt Steiger Werkzeugmaschinen GmbH
- Flachstr. 11
- 65197 Wiesbaden
- Deutschland
-
+49 (0) 611/421047
+49 (0) 611/421040 -
info@kurt-steiger.de
www.kurt-steiger.de
#2043-19334 · Plate Bending Machine - 3 Rolls
AKYAPAK - 1030 x 70 - - 1998 -
Technical details
working width: 1050 mm
metal sheet thickness: 1,5 mm
upper roller-Ø: 70 mm
below roller-Ø: 70 mm
Njw93ychg
weight: 320 kg
space needed: 700 x 1300 x 1100 mm
Datasheet
Request / Contact
- Kurt Steiger Werkzeugmaschinen GmbH
- Flachstr. 11
- 65197 Wiesbaden
- Deutschland
-
+49 (0) 611/421047
+49 (0) 611/421040 -
info@kurt-steiger.de
www.kurt-steiger.de
#2043-18062 · Plate Bending Machine - 3 Rolls
DURMAZLAR - KSM 56 - - 1996 -
Technical details
working width: 1030 mm
metal sheet thickness: 1 mm
upper roller-Ø: 60 mm
below roller-Ø: 60 mm
Zxy8p9m
weight: 170 kg
space needed: 560 x 1570 x 1080 mm
Datasheet
Request / Contact
- Kurt Steiger Werkzeugmaschinen GmbH
- Flachstr. 11
- 65197 Wiesbaden
- Deutschland
-
+49 (0) 611/421047
+49 (0) 611/421040 -
info@kurt-steiger.de
www.kurt-steiger.de
#2043-18062 · Plate Bending Machine - 3 Rolls
DURMAZLAR - KSM 56 - - 1996 -
Technical details
working width: 1030 mm
Iw8bipcy0
metal sheet thickness: 1 mm
upper roller-Ø: 60 mm
below roller-Ø: 60 mm
weight: 170 kg
space needed: 560 x 1570 x 1080 mm
Datasheet
Request / Contact
- Knops Werkzeugmaschinen
- Konrad-Zuse-Straße 5
- 40789 Monheim
- Deutschland
-
02173 - 39494-0
02173 - 39494-29 -
maschinen@knops.de
www.knops.de
#1022-H06661 · Plate Bending Machine - 3 Rolls
SCHAEFER - SRMVQ - - 1975 -
Technical details
Machine in good condition. PREBENDING DOUBLE . Maximum bending length 3.000 mm . Bending capacity 40 mm . Prebending capacity 30 mm . Top roll diameter 590 mm . Bending rolls diameter 490 mm . Main motor 45 kW . Bending motor 30 kW . Digital readout in all axis . Approximate weight 45 t . Approximate dimenssion.: . Length: 8.400 mm . Width: 2.600 mm . Height: 3.700 mm . Trench height: 1.780 mm
- Kurt Steiger Werkzeugmaschinen GmbH
- Flachstr. 11
- 65197 Wiesbaden
- Deutschland
-
+49 (0) 611/421047
+49 (0) 611/421040 -
info@kurt-steiger.de
www.kurt-steiger.de
#2043-26672 · Plate Bending Machine - 3 Rolls
unbekannt - unbekannt - - -
Technical details
working width: 1040 mm
Lp20uvs
metal sheet thickness: 1,25 mm
upper roller-Ø: 56 mm
below roller-Ø: 56 mm
weight: 190 kg
space needed: 1450 x 460 x 1030 mm
Datasheet
Request / Contact
- Kurt Steiger Werkzeugmaschinen GmbH
- Flachstr. 11
- 65197 Wiesbaden
- Deutschland
-
+49 (0) 611/421047
+49 (0) 611/421040 -
info@kurt-steiger.de
www.kurt-steiger.de
#2043-26395 · Plate Bending Machine - 3 Rolls
unbekannt - unbekannt - - -
Technical details
working width: 1020 mm
32qxc3xgp
metal sheet thickness: 1 mm
upper roller-Ø: 55 mm
below roller-Ø: 55 mm
space needed: 1370 x 570 x 1100 mm
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-217 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - RM 1050 x 90 - - -
Technical details
3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor lateral roll adjustable by handwheel longitudinal grooves in lower and lateral roll tiltable upper roll right / left rotation with double foot switch conical rolling device user manual in GERMAN
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-224 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - R 1270 x 68 - - -
Technical details
3 Walzen asymmetric rolls - prebending longitudinal grooves in lower and lateral roll Infeed of the lower roller by a central lever - with gear reduction machine stand user manual in GERMAN orENGLISH
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-1459 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - IRM 2050 x 140 - - -
Technical details
3 reels asymmetrical roller arrangement - with pre-bending 2 driven rollers by means of a brake motor manual Back Roll upper roller can be swiveled forward forward / reverse run conical rounding by inclining the rear rollers movable control panel OPTIONS: hardened Rolls€ 1.800,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,- (sample photo)
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-228 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - IR 1270 x 75 - - -
Technical details
3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor lateral roll adjustable by ratchet lever longitudinal grooves in lower and lateral roll tiltable upper roll hardened rollers right / left rotation with double foot switch user manual in GERMAN or ENGLISH
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-230 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - RS 1050 x 90 - - -
Technical details
3 rolls asymmetric rolls - prebending 2 rolls driven by handwheel lateral roll adjustable by handwheel longitudinal grooves in lower and lateral roll tiltable upper roll conical rolling device user manual in GERMAN
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-49 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - IRM 1050 x 130 - - -
Technical details
3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls€ 1.250,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,-
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-209 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - IRM 1550 x 140 - - -
Technical details
3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls€ 1.500,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,-
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-296 · Plate Bending Machine - 3 Rolls
HESSE by DURMA - MRB-S 2006 - - -
Technical details
3 rolls Asymmetrical rolls arrangement - with pre-bending 2 driven rolls Motorized adjustment of lateral and clamping roll Digital read-out for lateral and clamping roll Swiveling top roll to the front Forward/reverse run Hardened rolls Moveable control panel User manual in GERMAN and ENGLISH (sample photo)
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-205 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - IRM 1050 x 110 - - -
Technical details
3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls€ 1.120,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,-
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-215 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - RM 1270 x 90 - - -
Technical details
3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor lateral roll adjustable by handwheel longitudinal grooves in lower and lateral roll tiltable upper roll right / left rotation with double foot switch conical rolling device user manual in GERMAN or ENGLISH
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-213 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - RM 1550 x 90 - - -
Technical details
3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor lateral roll adjustable by handwheel longitudinal grooves in lower and lateral roll tiltable upper roll right / left rotation with double foot switch conical rolling device user manual in GERMAN or ENGLISH OPTIONS: powered back roll EUR 1.000,- digital readout EUR 1.100,-
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-290 · Plate Bending Machine - 3 Rolls
HESSE by DURMA - MRB-S 1506 - - -
Technical details
3 rolls Asymmetrical rolls arrangement - with pre-bending 2 driven rolls Motorized adjustment of lateral and clamping roll Digital read-out for lateral and clamping roll Swiveling top roll to the front Forward/reverse run Hardened rolls Moveable control panel User manual in GERMAN and ENGLISH (sample photo)
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-211 · Plate Bending Machine - 3 Rolls
HESSE by ISITAN - IRM 1270 x 140 - - -
Technical details
3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls€ 1.500,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,-
Datasheet
Request / Contact
TOP Manufacturer:
VIGANO/RIVA - HYDRO MECA - WILHELMSBURGER - HITACHI -