Cold rolling mills

Material Width 400 (420) mm︱Material Thickness 0,13 - 1,00 mm︱coil weight app. t︱Machine Weight app. 18,36 t︱Required Space app. m︱

---

2HI ROLLING MILL working direction right - left otherwise according to technical specification 04.12-2

---

consisting of: infeed unit complete mounted at fitting frame feeding unit manually (by hand wheel) / daylight width 265 mm plate brake unit hydraulically crop shear (cutting shear) hydraulically cutting process from below (by hydraulic cylinder) / blade length 350 mm run out table with press roll from above press roll length 350 mm / press roll – diameter 250 mm hydraulic valve mounted at frame construction control unit mounted at frame construction hydraulic unit not available infeed unit has been processed at a cold rolling mill

---

execution 8" 2HI COLD ROLLING MILL roll length 235 mm working direction left - right otherwise according to technical specification 04.12-1

---

AUMA GS250 Swing gear with gearbox type GZ 25.1 i = 8:1 M in = 200Nm M out = 1370Nm Temperature -25/+80°C and bevel gear type GK 14.2 i = 2:1 M a = 111Nm M out = 200Nm Dimensions 112x66x36cm 1. Flange Ø 17cm with 4 holes with shaft Ø 30mm and wavelength 65mm 2. Flange covered with outer diameter 29cm and 4 drill holes 3. Output flange Ø 535mm outside Ø 215mm inside with 8 screw holes unused Weight 340kg You can come and inspect the article at our warehouse in Giebelstadt about 80min. from FRANKFURT AIRPORT.

---

AUMA Swing gear with countershaft GS400 with GZ35.1 Overall ratio i= 1728:1 IP67 Tein = 190Nm Taus = 125000Nm Temperature -25...+80°C Motor shaft Ø 30mm x 63mm length Outer flange Ø 850mm with 8 drill holes Ø 27mm to Ø 700mm Inner flange Ø 173mm with 4 keyways Dimensions 1600x1080x480mm with acceptance report unused Weight 1176kg You can come and inspect the article at our warehouse in Giebelstadt about 80min. from FRANKFURT AIRPORT.

---

SPUR GEAR (condition AS NEW) Technical Data: drive power: P(Mot) = 610 kW driving speed: n(1) = 737 rpm driving speed: n(2) = 30,23 rpm transmission i = 24,38 : 1 starting moment: T(1) Mot = 7,9 kNm application factor: KA = 1 bearing life: L10h = 30.000 h inertia: Jred = 72964,54 kgm² (reduced on output) Oil filling: 1.500 l

plate width mm︱plate thickness mm︱no. of working stations Stück︱total power requirement kW︱weight of the machine ca. t︱dimensions of the machine ca. m︱

---

---

execution 6 HI ROLLING MILL working direction left - right unit consisting of: decoiler expanding process hydraulically hydraulically tiltable hydraulically movable press roll - motor driven brake - hydraulically mandrel diameter 400 mm incl. segments 500 mm mandrel length app. 460 mm 6 HI rolling mill with driver unit power mill 250 kW recoiler clamping hydraulically expanding process hydraulically shifting device hydraulically mandrel diameter 400 mm mandrel length app. 500 mm coil car - over floor - l-type hydraulically movable hydraulical lifting - lowering emulsion filter unit spare parts: no. - work rolls 24 work roll diameter app. 160 - 156 mm roll width app. 490 mm total length app. 1.280 mm no. - back up rolls 8 back up roll diameter app. 350 - 360 mm roll width app. 446 mm total length app. 1.180 mm electric equipment not available * this thickness has been processed by the previous operating company

---

Execution 6 HI ROLLING MILL coil inside diameter 400 mm (500 mm with segments) coil outside diameter 1.500 mm otherwise according to technical specification 04.02-4